CalcTypes
Calculator

Cut List Optimizer & Linear Cutting Calculator

Last updated: Β·MethodologyΒ·Questions People AskΒ·Sources
Free 1D Cut List Optimization Tool

Use Existing Stock First & Build Practical Cutting Patterns

Optimize bars, rods, pipe, tube, timber, mouldings, steel sections, aluminium extrusion and other linear stock. Use compatible stock lengths and reusable offcuts you already own before buying new material. If your application allows joints, a longer finished run can also be planned from sensible segments instead of simply failing when no single stock length is long enough.

Primary rule: available compatible stock comes first. CalcTypes challenges the whole job against your existing full lengths and remnants before it accepts a new purchase. In joined-run mode, it also avoids impractical tiny segments by respecting your minimum segment size and maximum-joint limit.

New here? Try a ready-made cut-list example

Optional examples for a homeowner, contractor/fabricator or supplier. Open this only if you want a quick demonstration before entering your own job.

Homeowner / DIYEnter the lengths you need and the stock you already have. The result shows whether you really need to buy more.
Contractor / workshopUse part marks, cutting loss, trim and cutting cards to turn a schedule into repeatable fabrication instructions.
Supplier / fabricatorEnter yard stock, remnants, standard purchasable lengths and prices to see the genuine shortage and estimated order cost.
AvailableFull stock + usable remnants
UsedWhat the plan actually consumes
RemainingUnused existing lengths
ShortageOnly what inventory cannot cover
BuyNew stock + optional buffer
Tip: load an example, then replace the values with your own job.
1

First, choose how your finished lengths may be made

This is the main decision. One-piece mode is preselected as the safe default, but please choose the option that matches your real job before entering the rest of the data.

START HERE β€” choose how the finished length may be made
One-piece mode: every required final length must come from one continuous stock piece.
2

Set the project & result units

Every stock length and required length has its own unit selector. The result unit below only controls how dimensions are displayed and which unit new rows use.

Project / job details (optional β€” shown on report)
3

Enter stock lengths & reusable offcuts

Add full lengths already in your yard, useful remnants/offcuts, and standard supplier lengths. A quantity of 0 with β€œCan purchase?” set to Yes means a supplier-only option.

Match group: only stock and requirements with the same group can be mixed. Leave everything as A for one compatible material. Use B, C, etc. when profiles, sizes, grades or materials must stay separate.

Stock / offcut labelMatch groupLengthQty availableCan purchase?Price / length
4

Enter the required final lengths

Enter the final length you need. Give each type a short mark such as A, B or P01. In joined-run mode, rows marked β€œYes” may be split into a few practical segments when that reduces genuine new purchases.

Part / markWhere used (optional)Match groupRequired final lengthQtyCan be joined?
Paste stock from Excel / CSV
Header-aware. Simple rows such as 6000,3,24 also work.
Paste cut list from Excel / CSV
Header-aware. Simple rows such as A,1800,20 also work.
Advanced cutting & purchasing settings
Material removed by each cut.
Total unusable length reserved from each used stock piece.
Default: 0%.
This is only a tie-breaker. Existing compatible stock is still tested first.
Always enabled. Compatible existing stock and offcuts are tested before supplier stock.

Your inventory-first cutting plan

β€”Existing lengths available
β€”Existing lengths used
β€”Existing lengths remaining
β€”New lengths genuinely required
β€”Order qty incl. optional buffer
β€”
Finished-piece utilization
β€”
True scrap / loss
β€”
Reusable leftover
β€”
Estimated order cost
β€”
Physical cuts
Planning tool: the browser uses an exact inventory-only feasibility search for manageable match groups and multiple deterministic cutting-stock strategies for larger jobs. It does not claim a mathematical global optimum for every very large industrial problem.

1. Available β†’ used β†’ remaining β†’ genuine shortage

This is the purchasing audit. New stock appears only when the compatible inventory entered cannot complete the cut list.

2. Quick workshop cutting summary

Use this as the short cutting instruction sheet: take this stock β†’ repeat this pattern β†’ make these cuts on EACH length β†’ check the total output β†’ keep or scrap the leftover.

3. Required-piece verification

4. Visual cutting patterns & workshop cards

Finished parts use distinct colors. Green means reusable leftover, red means scrap, light grey is kerf/cutting loss and dark grey is unusable trim.

5. Reusable leftovers to keep

These remnants meet your reusable threshold and should return to stock instead of being counted as waste.

6. Material & optimization breakdown

How this plan was calculated

    Share, print or send the exact cutting plan

    Print creates a dedicated compact report rather than printing the whole webpage. The exact project link, QR and Project JSON can reopen the same inputs on another device.

    Anyone with this exact link can read the project inputs encoded in it. For a large job, send the Project JSON as a backup.

    CTCutting reports and cards are branded CalcTypes.com so the plan can be traced back to the calculator.

    Scan this cutting plan

    Open the same stock, cut list and settings on another device.

    Linear Cut List Optimizer for Bars, Pipe, Tube, Timber & Profiles

    This free cut list optimizer is a browser-based cut list calculator for one-dimensional stock. It handles bars, rods, pipe, tube, timber, mouldings, steel sections, aluminium extrusion and similar materials. You can keep every requirement as one continuous piece, orβ€”when your application safely allows itβ€”plan a longer finished run from a small number of practical joined segments.

    Unlike a simple length total, cut list optimization must consider the actual combination of piece lengths, kerf, end trim, existing stock, reusable offcuts, purchasable stock sizes and compatibility. A job can have enough total metres on paper and still require another stock length because the pieces do not physically fit into the available remnants.

    How to use the linear cutting calculator

    1. Choose One-piece cuts only or Joined runs allowed.
    2. Enter full stock lengths and usable remnants already available.
    3. Add supplier lengths with quantity 0 and purchasing enabled.
    4. Enter the required final lengths and quantities.
    5. Use Match groups to keep incompatible materials or profiles separate.
    6. Open Advanced settings only if you need to change blade width, trim, reusable-leftover size or purchase preferences.
    7. Optimize, then verify the cutting patterns, assembly plan (when joining is used) and genuine purchase shortage.

    Why reusable offcuts matter

    A leftover is not automatically waste. If a remnant is long enough to be useful, CalcTypes records it separately so it can return to inventory. True scrap is limited to cutting loss, trim and short unusable remnants.

    How the Cut List Optimizer Solves a 1D Cutting Stock Problem

    The calculator models the cutting stage as a one-dimensional cutting stock problem. In one-piece mode, each required final length is indivisible. In joined-run mode, rows that permit joining are first given several practical segment recipes that obey the maximum-joint, minimum-segment and joint-allowance rules; those cut segments are then packed into compatible stock lengths while accounting for cutting loss and end trim.

    The commercial priority is deliberately different from a waste-only optimizer: complete the job, minimize the number of new stock lengths, compare purchase cost where prices are known, minimize total purchased length, then prefer fewer joints in joined-run mode, and only after that use waste, stock count and other neatness measures as tie-breakers. The minimum-segment rule prevents the optimizer from using tiny scraps merely to avoid a purchase.

    For manageable Match groups, a bounded exact inventory-only feasibility search runs before a purchase is accepted. If that search proves the pieces can be cut from compatible existing inventory, a purchase plan is rejected. Larger groups are tested with many deterministic piece orders, ways of filling inventory and supplier-stock choices. Purchased cutting patterns are then right-sized against compatible supplier lengths so the same cuts are not left on an unnecessarily long stock length when a shorter or lower-cost option is available.

    Assumptions & Limitations

    • The model is for one-dimensional linear cutting. Plywood, glass, tile and stone sheet/slab nesting need a 2D optimizer.
    • Only identical Match groups are interchangeable. Use different groups for different material, grade, section/profile, diameter, finish, batch or any other constraint that prevents substitution.
    • In one-piece mode, the entered final length must come from one continuous stock piece. In joined-run mode, the entered value is the required finished run length and the calculator may divide it into segments only for rows where joining is allowed.
    • Joined-run mode is a length-planning feature, not joint engineering. The calculator does not certify joint strength, splice type, weld detail, connector type, location, pressure suitability or code compliance. Use the joint allowance only for known overlap/end-preparation length supplied by your design or fabrication method.
    • Kerf is treated as material lost between adjacent pieces and before a leftover is separated.
    • Very large cutting-stock problems can become combinatorial. The bounded exact inventory check is intentionally size-limited; larger jobs use multiple deterministic heuristics and should be verified before a high-value order.
    • Prices are optional and exclude freight, taxes, labour and supplier minimum-order rules unless included in your own inputs.

    Questions People Ask About Cut List Optimization

    Practical answers for people using a cut list calculator, workshop optimizer or cutting stock planner.

    What is a cut list optimizer?

    A cut list optimizer arranges required finished lengths across available stock lengths so the pieces can be produced with fewer new purchases and less true waste.

    This calculator is for 1D stock such as bars, pipe, tube, timber and extrusion.

    What is the cutting stock problem?

    The cutting stock problem asks how standard stock lengths should be cut to produce a required set of smaller lengths while minimizing a chosen resource such as new stock, cost or waste.

    Simple example: needing 2.4 m, 2.4 m and 1.0 m from 6 m stock is not just a total-length calculation; kerf and the way pieces share each stock length matter.

    How do I use a cut list optimizer?

    Enter the compatible stock you already have first, then the required finished pieces.

    Add purchasable standard lengths with quantity 0, set realistic kerf/trim values and optimize. Read the result as Available β†’ Used β†’ Remaining β†’ Genuine shortage β†’ Buy.

    What if the finished length I need is longer than every stock piece?

    If the real application allows a joint, choose Joined runs allowed. The calculator can make the finished run from a few practical segments while respecting your maximum-joint and minimum-segment rules.

    For example, a 7.5 m run may be planned from 3 m + 3 m + 1.5 m stock pieces when that is compatible with your job.

    If the application requires one continuous member, keep One-piece cuts only; the calculator will then tell you that longer compatible stock is required instead of silently inventing a joint.

    How many new stock lengths do I actually need to buy?

    The genuine shortage is the number of new lengths the optimized plan still needs after existing compatible inventory has been tested.

    An optional buffer is shown separately and does not alter that underlying shortage.

    Can existing bars and offcuts be used before buying new stock?

    Yes. That is the primary rule.

    Existing full lengths and reusable remnants in the same Match group are evaluated first. For manageable groups, the calculator also performs an exact inventory-only feasibility check before accepting a purchase.

    How does a cut list calculator account for saw kerf?

    Kerf is the width removed by the blade or process.

    The optimizer reserves the entered kerf between adjacent pieces and, where needed, before separating the final leftover. It is reported as cutting loss rather than reusable material.

    Can 6 m, 9 m and 12 m stock lengths be optimized together?

    Yes. Add each stock size as its own row.

    Existing quantities can be mixed with purchase-only rows, and reusable odd-length remnants can be entered as stock too.

    What is the difference between reusable leftover and scrap?

    A final remnant at or above your reusable threshold is kept as useful stock. Shorter leftover, trim and kerf are reported as true scrap/loss.

    This prevents a valuable offcut from being incorrectly counted as waste.

    Is the lowest-waste cutting pattern always the cheapest plan?

    No. A plan can have slightly lower waste but still require an unnecessary new length. CalcTypes therefore minimizes new stock count before waste.

    When comparable purchase prices are available, purchase cost is considered next; total purchased length is then minimized before secondary neatness preferences.

    Is the cutting plan guaranteed to be the mathematical global optimum?

    Not for every possible large job.

    For manageable groups, the inventory-only check can prove a zero-purchase solution when one exists within the bounded search size. After that, the general cutting stock problem can become very large, so CalcTypes tests several deterministic heuristics and clearly reports this limitation.

    Important disclaimer

    Sources & Technical References

    These references provide background for the packing and cutting-stock terminology used on this page. The CalcTypes browser algorithm is an independent implementation.

    1. Google OR-Tools β€” The Bin Packing Problem. General background on assigning items to capacity-constrained bins while minimizing the number of bins.
    2. Delorme, Iori & Martello β€” Bin packing and cutting stock problems: Mathematical models and exact algorithms, European Journal of Operational Research, 255(1), 2016. Review of mathematical models and exact methods for bin-packing and cutting-stock problems.