Cement Types, Grades and Uses
What are the different types of cement and what are they used for?
Portland and blended cements are used in many building concretes, masonry cement is made for mortar, and specialist cements serve jobs that need properties such as fast strength gain or low heat.
Start with what you are building. A footing, a brick wall and a bathroom each call for a different kind of mix or installation system. This guide explains how to read a bag label, compare cement types and work out how much material to buy.
What is cement, and how is it different from mortar and concrete?
Cement is a powdered binder that reacts with water to form a hard material.
For an ordinary building job, you will usually use it as one ingredient in mortar or concrete.
What is cement paste?
Cement mixed with water forms a paste. The reaction with water is called hydration.
What is mortar?
Mortar is a mixture of binder, fine aggregate such as sand, and water.
Depending on the mix, it can join masonry units or form a plaster coat.
What is concrete?
Concrete combines cementitious material and water with fine and coarse aggregates, such as sand and crushed stone.
It is used for work such as footings, slabs, beams and columns.
How is Portland cement made?
Manufacturers heat a prepared mineral mix in a kiln to make clinker, then grind it with a small amount of gypsum or another permitted calcium sulfate source.
Limestone supplies much of the calcium. Clay or other materials supply other ingredients, including silica and alumina. Calcium sulfate helps control setting. Blended cements also use specified constituents such as fly ash, ground slag, calcined clay or limestone, depending on the cement type.
Which properties of cement matter on site?
The most useful things to understand are setting time, early strength, heat generation and durability under the expected exposure.
These affect how the product is handled and what the project may specify.
- Setting time. The mix gradually loses plasticity after water is added. Plan the placing and finishing work around the specified material and site conditions.
- Strength gain. A mix can feel firm long before it reaches the strength required for loading or removing supports. The projectβs approved criteria govern those decisions.
- Heat of hydration. The cement-water reaction generates heat. Thick pours can retain more heat and may need a designed temperature-control plan.
- Curing. Keep the concrete or mortar under the moisture and temperature conditions specified for the job so it can develop the intended properties.
- Durability. Exposure to seawater, groundwater or chemicals can change the mix requirements. The binder, water content, cover to reinforcement, placement and curing all matter.
American Cement Association on cement manufacturing Β· Cement and concrete FAQ
What is the difference between OPC, PPC and PSC cement?
OPC is Ordinary Portland Cement, PPC contains a pozzolanic material, and PSC contains granulated blast-furnace slag.
Each has a separate Indian Standard. For a homeowner, the important comparison is what the approved mix calls for, how soon the work needs to gain strength and what it will be exposed to.
Ordinary Portland Cement. You may see OPC specified for ordinary concrete or for precast work, where pieces such as steps or panels are cast in moulds before installation. If the precast piece needs to come out of the mould on a tight schedule, the strength it has gained by that time matters.
Portland Pozzolana Cement. Fly ash or calcined clay contributes to the binder as the mix hardens. Two mixes that both meet the specified strength at 28 days can gain strength at different rates in the first few days. When PPC is proposed, ask how the mix will be cured and when it needs to reach its early strength targets.
Portland Slag Cement. Slag is a material recovered from ironmaking and processed for use in cement. A designer may consider a slag-containing mix for a thick foundation where heat is a concern or for concrete exposed to certain salts. In either case, the project team checks how the whole mix performs under those conditions.
| Cement type | Indian Standard | Why it may be considered | What to confirm |
|---|---|---|---|
| Ordinary Portland Cement (OPC) | IS 269 | General concrete and work with a specified early-strength requirement, such as some precast production. | The exact grade and the approved mix for the job. |
| Portland Pozzolana Cement (PPC) | IS 1489, Part 1 or Part 2 | General building concrete and suitable masonry or plaster mortar. A project may allow it where the proposed mix meets the required strength and durability. | Which PPC variant is supplied, plus the strength-development and curing requirements. |
| Portland Slag Cement (PSC) | IS 455 | General concrete and some large pours or exposure-sensitive projects when approved. | Suitability of the complete mix for the actual exposure and construction schedule. |
Which is better for house construction, OPC or PPC cement?
Either can be suitable when the approved concrete or mortar specification allows it.
If a contractor suggests changing an approved product, ask how the proposed mix meets strength, exposure and curing requirements. For brickwork or plastering, ask for the mortar specification for that particular area of the house.
What is the difference between PPC and PSC?
PPC uses a pozzolanic material such as fly ash or calcined clay. PSC uses slag.
A pozzolan reacts with compounds formed during cement hydration and contributes to the hardened binder. A slag-containing cement can also change how the mix gains strength and behaves in service. The exact product, proportioning and curing determine how those differences apply to your job.
What is the difference between cement type, cement grade and concrete grade?
Cement type tells you what kind of binder is in the bag. Cement grade describes how it performs in a standard mortar strength test.
Concrete grade describes the strength required of the finished concrete mix.
What does the cement type tell you?
The type identifies the cement family or performance category. For example, Ordinary Portland Cement (OPC) and Portland Slag Cement (PSC) are different types.
The label and standard tell you which product you are buying.
What does the cement grade tell you?
In the Indian label OPC 53, OPC is the type and 53 is the grade. The number refers to a minimum 28-day strength of 53 MPa in a standard cement-mortar test.
What does the concrete grade tell you?
On an Indian drawing, M25 specifies a characteristic strength of 25 MPa at 28 days, measured on concrete cubes.
That requirement applies to the concrete made with cement, water, sand and coarse aggregate.
Example. If your roof slab drawing says M25, ask for the approved M25 mix or ready-mix reference. That tells the supplier what concrete to deliver. The approved mix specifies which cement to use. If you see OPC 53 on a bag, read it as a property of the cement inside.
BIS standard for Ordinary Portland Cement Β· Indian Railways concrete mix design checklist
What do OPC 33, 43 and 53 cement grades mean?
They identify Ordinary Portland Cement with minimum 28-day compressive strengths of 33, 43 and 53 MPa respectively, measured on standard cement-mortar specimens under IS 269.
One MPa equals one newton per square millimetre (N/mmΒ²).
| OPC grade | 3 days | 7 days | 28 days |
|---|---|---|---|
| OPC 33 | 16 MPa | 22 MPa | 33 MPa |
| OPC 43 | 23 MPa | 33 MPa | 43 MPa |
| OPC 53 | 27 MPa | 37 MPa | 53 MPa |
Read across the row for the grade on your bag. Each column is a separate laboratory strength requirement at that age. For example, the 28-day figure for OPC 43 is the minimum for a standard mortar specimen. For your slab, the strength requirement comes from the approved concrete specification.
What is the difference between 43 grade and 53 grade cement?
OPC 53 has higher minimum mortar strengths at the specified test ages than OPC 43.
That can matter in work such as precast production with an early-strength requirement. Use the grade approved for the mix. A higher number on the bag alone gives no basis to change that approval or remove formwork earlier.
BIS IS 269 Β· Indian Railways summary of OPC strength requirements
Which cement or material should I use for my projects?
Choose what youβre building. Get a first choice and two alternatives for each project. If you already have cement or a mix in mind, enter what is printed on the bag or delivery ticket to see how it fits that job.
Use Show recommendations for material advice alone. To estimate quantities, open Add measurements for the projects you want to measure, then click Calculate quantities.
For structural work, use the mix approved for your project. The ranked options show where to start and when an alternative may make sense. An option can suit your job even if it appears lower in the list. The drawings and mix specification govern the strength, exposure requirements and any substitution.
Enable JavaScript for the planner, or use the job-by-job guide and Concrete Volume Calculator.
Your project results
BIS cement compendium Β· American Cement Association cement types Β· Example wet-room systems Β· Example repair mortar application limits
Which cement is best for house construction?
Use the cement specified for the part of the house you are building.
A house can have different requirements for a reinforced footing, a brick wall and a bathroom. Identify the job first, then ask for the applicable mix, mortar or installation specification before you buy.
What should you order for a roof slab, pillar or footing?
Ask for the concrete mix specified for that part of the structure.
A concrete supplier needs the mix reference and volume. If a builder will mix it on site, ask for the approved cement type and how many kilograms of it go into a cubic metre of concrete. A bag labelled OPC 53 tells you about the cement inside. The engineerβs mix specifies the concrete that goes into the structure.
Worked example. A 20 mΒ² slab at a specified thickness of 150 mm contains 3 mΒ³ of concrete before allowances. Four rectangular pillars measuring 300 mm by 300 mm by 3 m add 1.08 mΒ³ if their heights are measured clear of the slab. Enter them as two jobs. Ask the project team whether both jobs use the same approved mix and whether the pours will be ordered together.
What changes for a basement parking floor or a retaining wall?
Find out whether the concrete is a structural element, a floor on the ground or a finish laid over an existing slab.
A basement can need all three, plus a separate water-control system. For example, the parking slab may need an approved mix and surface finish for vehicles. A basement retaining wall has its own design for the earth and water it holds back. Keep those jobs separate when asking for quantities and quotes.
Sulfates in some soil or groundwater can damage concrete. Chlorides can corrode the steel inside it. Give the project team the site exposure information before selecting a cement family or accepting a substitution.
What should you buy for a brick or block wall?
Ask for a mortar compatible with the bricks or blocks and the specified joint thickness.
Ordinary brickwork may use the builderβs specified site-mixed mortar or a compatible bagged masonry mortar. Some accurate-size blocks use a thin-bed adhesive instead. Ten square metres of wall can use very different amounts of mortar with different block sizes and joints. For a packaged product, use the coverage for your units and joint size.
How do you estimate cement or render for wall plastering?
Measure the surface to cover, then use the specified plaster thickness or the packaged renderβs coverage at that thickness.
For example, a 4 m by 3 m wall with a 2 mΒ² opening has 10 mΒ² to plaster, before any window or door reveals. If the chosen product covers 2.5 mΒ² per bag at the specified thickness, four bags cover the measured area before allowances. Count both faces if both are being plastered. Ask separately about exterior render, where the wall and weather exposure matter.
What do you need for a bathroom floor or flat roof?
List the layers separately.
A bathroom floor may need a screed to form the slope, a waterproofing system at the floor, wall junctions and drain, and a tile adhesive matched to the tiles and backing. Use the coverage for the selected adhesive and trowel. Use the waterproofing systemβs total coverage for the required coats and details. For a flat roof, enter the structural slab and the roof waterproofing as separate jobs, using the specified roof system and the area it actually covers.
Indian Railways concrete mix design checklist Β· ACI guide to cementitious materials and exposure Β· Example wet-room installation systems
What are the different types of cement and their uses in India?
The BIS cement compendium lists 16 cement entries, including two PPC variants.
The directory below names all 16 and explains their purpose. These entries include specialist products, and retail availability varies. The edition year is shown where a later revision is particularly relevant.
If you are buying for general building work, start with the cement type written in your specification and look up its IS number below. Specialty names often tell you which problem the product addresses. White cement is often chosen for the appearance of a finish. Rapid-hardening cement can help a repair reach its strength target sooner, while low-heat cement addresses heat buildup in a large pour. Oil-well cement and microfine grouting cement are examples of products designed for specific placement conditions.
| Type of cement | BIS reference | What it is and where it may be used |
|---|---|---|
| 1. Ordinary Portland Cement (OPC) | IS 269 | General Portland cement for approved concrete and mortar mixes. Common grade labels include 33, 43 and 53. The standard also includes 43S and 53S for specialist use such as railway sleepers. |
| 2. Portland Pozzolana Cement, fly ash-based | IS 1489, Part 1 | Blended PPC containing fly ash as the pozzolan. It may be used for suitable building concrete, masonry mortar or plaster where specified. |
| 3. Portland Pozzolana Cement, calcined clay-based | IS 1489, Part 2 | Blended PPC using calcined clay as the pozzolan. It may be used in approved building and infrastructure mixes. |
| 4. Portland Slag Cement (PSC) | IS 455 | Contains granulated blast-furnace slag. It can be considered for general concrete and selected large pours or exposure-sensitive mixes. |
| 5. White Portland Cement | IS 8042 | A light-coloured Portland cement used for applications such as architectural finishes, terrazzo and decorative castings. Follow the finish or product specification. |
| 6. Composite Cement | IS 16415 | A Portland-based blend with slag and fly ash. Use it for concrete or other work where the project accepts that blend. |
| 7. Masonry Cement | IS 3466 | Formulated for mortar in brick or block masonry, plastering and rendering. For structural concrete, use the binder called for by the approved concrete mix. |
| 8. High Alumina Cement for Structural Use | IS 6452:2026 | A specialist binder subject to specific material and application requirements. Use only where the project specification calls for it and the design team has addressed the applicable restrictions. |
| 9. Supersulphated Cement | IS 6909:2026 | A specialist cement based mainly on slag with a sulfate component and an activator. It may be specified for selected sulfate exposure conditions. |
| 10. Rapid Hardening Portland Cement | IS 8041:2026 | Develops strength earlier for work with a specified early-strength target. Possible applications include precast work or certain repair projects. |
| 11. Hydrophobic Portland Cement | IS 8043:2026 | Designed to help limit the effects of atmospheric moisture on dry cement during storage or handling. Waterproofing a bathroom or roof still requires a suitable installation system. |
| 12. Oil-Well Cement | IS 8229 | Engineered for specialist cementing work in wells, where conditions and placement requirements differ from ordinary building work. |
| 13. Sulphate Resisting Portland Cement | IS 12330 | A cement designed for specified sulfate exposure, such as some soils or groundwater. The exposure assessment and complete concrete mix govern its suitability. |
| 14. Low Heat Portland Cement | IS 12600 | Designed to limit heat generation from hydration. It may be specified for mass concrete or other large pours that need a temperature-control plan. |
| 15. Microfine Ordinary Portland Cement | IS 16993 | Very finely ground cement for specialist grouting work. Its fine particles help the grout enter small openings when the application and grout design allow. |
| 16. Portland Calcined Clay Limestone Cement | IS 18189:2023 | A blend containing calcined clay and limestone. You may see the term LCΒ³ or LC3 for this binder family. Check the bag or technical data sheet for the declared specification. |
The names and reference numbers are based on the BIS compendium. Check the applicable edition and amendments for procurement. BIS compendium Β· March 2026 Gazette notification transcript
What do other cement and construction product names mean?
Terms such as quick-setting cement, waterproofing compound and tile cement describe a property, a product or a use.
Ask for the exact product name, specification and technical data sheet. The terms below are grouped separately from the 16 BIS compendium entries.
Is quick-setting cement the same as rapid-hardening cement?
Quick-setting describes how soon a product stiffens. Rapid-hardening describes how quickly it gains strength.
A repair product can have both properties. Check its working time and strength at the age that matters for the repair.
What does waterproof cement mean?
It usually means cement with an integral waterproofing compound (covered by IS 2645 in India) or a separate coating, so ask the supplier which one they mean.
Ask whether the supplier means a branded cement, an integral waterproofing compound or a coating. IS 2645 covers integral waterproofing compounds for cement mortar and concrete. For a leaking area, the specified system may also need treatment at joints and penetrations.
What is expansive cement?
It is a specialist hydraulic cement formulated to expand under specified conditions.
One example of a specification is ASTM C845. For a job requiring a non-shrink grout or shrinkage compensation, check the specific product and project requirements.
What are white cement and coloured cement used for?
They are commonly associated with architectural and decorative finishes.
White Portland cement has its own BIS reference, IS 8042. A coloured finish may use pigment in a specified cement-based mix or a factory-made product.
What do people mean by tile cement?
They often mean a cement-based tile adhesive or the mortar used to bed tiles.
Check the tile, substrate and service conditions when choosing the installation system. BIS lists adhesives for ceramic, mosaic and stone tiles under IS 15477.
Is horticultural cement a cement grade?
Horticulture describes a use, such as casting a garden planter. It is absent from the 16-entry BIS cement compendium.
For a planter, check the casting mix or product instructions. If the term you heard was hydrophobic cement, that is the separate IS 8043 entry for dry cement moisture protection.
BIS manual for integral waterproofing compounds Β· BIS tile adhesive listing Β· ASTM expansive hydraulic cement specification
How do you read a cement bag label before buying?
Match the cement type, grade where applicable, and standard number to the order.
Then check the net weight, packing details and any applicable certification markings. Ask for the technical data sheet if the front of the bag mainly shows a brand name. The example below uses an Indian label. The international comparison shows how other standards describe their products.
- Ordinary Portland Cement, OPC 53
- OPC is the cement type. 53 is the grade within that type.
- IS 269
- The Indian Standard used to identify Ordinary Portland Cement.
- Net quantity 50 kg
- The example bag contains 50 kg of cement. Use the weight printed on the bag you are ordering.
- BIS Standard Mark and CM/L number
- Where applicable, use the licence number to check the certification details through BIS Care.
- Manufacturer, batch and packing date
- Record the batch if needed for traceability. Follow the productβs best-before or retesting instructions and check that the bags have been stored dry.
What should you check when cement is delivered?
Compare the bags with your order and flag any mismatch, damaged packaging, signs of dampness or unexplained hard lumps before use.
Keep the delivery paperwork and store the bags dry according to the supplierβs instructions. If a bag is old, damp or otherwise questionable, ask the supplier and project team how to handle it.
How do you calculate how many cement bags to buy?
Divide your estimated cement mass by the net weight of one cement bag, then round up to a whole bag.
The mass and bag weight must use the same unit.
Worked example. For an estimate of 317 kg, divide 317 by 50 to get 6.34. Round up to 7 bags of 50 kg. If the supplier offers 25 kg bags, 317 divided by 25 is 12.68, so order 13 bags of 25 kg.
Seven 50 kg bags supply 350 kg. Thirteen 25 kg bags supply 325 kg. That difference comes from rounding each order to whole bags. Compare delivered prices using the number of bags you actually need.
Which calculator should you use for cement or premixed concrete?
Use the Concrete Mix Calculator for separate ingredients and the Concrete Bag Calculator for dry premixed concrete.
With premixed concrete, use the supplierβs stated yield per bag. The pack weight includes the aggregates and other contents.
How do US and international cement labels compare?
A US label may identify an ASTM cement type, while a European label can combine a cement family, strength class and early-strength suffix.
Read each designation under its own standard before comparing products.
For example, the Roman numeral in US Type III identifies a cement intended for high early strength. In the European label CEM II/A-L 42.5 N, the 42.5 is a strength class and N describes the early-strength category. If a local supplier proposes a product with a different designation from the one on your plans, ask which standard it meets and have the project team check it against the specification.
| Region | Example designation | How to read it |
|---|---|---|
| United States | ASTM C150 Type I, II, III or V | General use, moderate sulfate resistance, high early strength or high sulfate resistance, respectively. |
| United States | ASTM C595 Type IL and ASTM C1157 Type GU or LH | IL is Portland-limestone cement. GU and LH are performance designations for general use and low heat. |
| UK and Europe | EN 197-1 CEM II/A-L 42.5 N | CEM II/A-L is a Portland-limestone designation, 42.5 is the strength class and N indicates normal early strength. R indicates high early strength. EN 197-5 covers CEM II/C-M and CEM VI. |
| Canada | CSA A3001 Type GU or GUL | GU is general-use Portland cement. GUL is general-use Portland-limestone cement. |
| Australia | AS 3972 Type GP, GB, HE or LH | General purpose, general-purpose blended, high early strength or low heat, respectively. |
What is Type IL cement in the US?
Type IL is Portland-limestone cement under ASTM C595. It is widely used in US concrete.
If an approved mix calls for a different cement type, check the substitution with the project team.
Type IV and Type II(MH) appear in older US references. The published scope of ASTM C150/C150M-24 lists I, IA, II, IIA, III, IIIA and V. ASTM C150 scope Β· American Cement Association on blended cements
Common questions about cement grades and types
Select a question to expand its answer.
What types and grades of cement are used in India?
Common Indian cement types include OPC, PPC and PSC. The familiar 33, 43 and 53 strength grades are for OPC under IS 269.
PPC is covered by IS 1489 and PSC by IS 455, each with its own requirements. See the complete BIS cement directory for all 16 entries, including masonry, white, hydrophobic and other specialty cements.
What does Grade 33 cement indicate?
OPC 33 indicates a minimum 28-day compressive strength of 33 MPa on standard cement-mortar specimens under IS 269.
Concrete made with it has its own strength requirements.
What grade is IS 1489 cement?
IS 1489 is the standard number for PPC. Part 1 covers fly ash-based PPC and Part 2 covers calcined clay-based PPC.
Each sets its own requirements. The OPC grade labels 33, 43 and 53 belong to IS 269.
What is the IS code for OPC 43 and OPC 53 cement?
IS 269:2015 covers both OPC 43 and OPC 53.
In older references you may see IS 8112 for OPC 43 and IS 12269 for OPC 53. BIS consolidated those grade specifications under IS 269.
Can you use PPC cement for brickwork and plastering?
Yes, where the specified mortar or plaster mix allows PPC.
Confirm the mix and curing requirements for the masonry units or surface being plastered. Some systems, including certain blockwork systems, call for a packaged mortar with its own instructions.
Can you switch between OPC and PPC during a structural pour?
Get the project engineerβs approval before making a change.
A different cement can change how the mix behaves and gains strength. Check the approved mix, supply arrangements and any required verification before continuing.
Does the packing date on a cement bag matter?
Yes. It helps identify the batch and tells you when to check the productβs best-before or retesting instructions.
Storage conditions also matter. Keep the bags dry and check with the supplier or project team if the product condition is uncertain.
Is hydrophobic cement used to waterproof a bathroom?
Hydrophobic Portland cement helps protect the dry powder from atmospheric moisture during storage or handling.
A bathroom needs a waterproofing system suitable for its surfaces, joints, drains and penetrations.
Methodology: How This Guide Works
Cement types, grades and standard numbers on this page are taken from the Bureau of Indian Standards (BIS) cement standards and compendium, with US and European equivalents from ASTM and EN standards where noted. Product terms are explained in plain language for homeowners and builders.
Assumptions and Limitations
Assumptions
- Indian grades follow BIS standards such as IS 269 (OPC) and IS 1489 (PPC).
- Concrete grades such as M20 or M25 are set by the structural design, not by the cement grade alone.
- Products are stored and used as the manufacturer directs.
Limitations
- Standards are revised from time to time; check the current BIS edition.
- This guide does not replace a mix design or an engineerβs specification.
- Brand products may have extra properties not covered here.
Sources and standards
Check the edition and amendments required by the project before procurement. The links below cover the material classifications, tests, and examples used in this guide.
- BIS compendium of Indian cement standards
- BIS implementation circular for IS 269:2015
- BIS OPC marking and testing guidance
- BIS product manual for Portland calcined clay limestone cement
- BIS reference for hardened-concrete testing under IS 516
- March 2026 Gazette notification transcript for IS 6909, IS 8041 and IS 8043
- BIS catalogue entry for IS 6452:2026
- American Cement Association comparison of ASTM cement types
- BS EN 197-1 and BS EN 197-5
- American Cement Association technical report on Portland-limestone cement and Canadian designations
- Australian concrete industry summary of AS 3972
Related concrete calculators
Disclaimer
Please read before relying on this page. This page on Cement Types, Grades and Uses gives general construction information for planning. Building codes, soil, loads and materials vary by location and project. It is not engineering or code-compliance advice; have structural work designed and checked by a qualified engineer or licensed contractor.
Construction. Quantities and costs are planning estimates only; follow local building codes and safety rules.
Your responsibility. Results are estimates for general information and education only, and nothing here is professional advice. You use this page at your own risk; to the fullest extent permitted by law, CalcTypes, its authors and reviewers accept no liability for loss, injury or damage arising from reliance on it. Spotted an error? Use βReport an issueβ or our contact page. Full terms: Disclaimer Β· Terms of use.